53 34 Pascal’s Principle, the Continuity Equation, and Bernoulli’s Principle
There are a couple of mistakes that tend to crop up with some regularity in the application of the Bernoulli equation . Firstly, folks tend to forget to create a diagram in order to identify point 1 and point 2 in the diagram so that they can write the Bernoulli equation in its useful form: . Secondly, when both the velocities in Bernoulli’s equation are unknown, they forget that there is another equation that relates the velocities, namely, the continuity equation in the form which states that the flow rate at position 1 is equal to the flow rate at position 2.
Pascal’s Principle
Experimentally, we find that if you increase the pressure by some given amount at one location in a fluid, the pressure increases by that same amount everywhere in the fluid. This experimental result is known as Pascal’s Principle.
We take advantage of Pascal’s principle every time we step on the brakes of our cars and trucks. The brake system is a hydraulic system. The fluid is oil that is called hydraulic fluid. When you depress the brake pedal you increase the pressure everywhere in the fluid in the hydraulic line. At the wheels, the increased pressure acting on pistons attached to the brake pads pushes them against disks or drums connected to the wheels.
Example 34–1
A simple hydraulic lift consists of two pistons, one larger than the other, in cylinders connected by a pipe. The cylinders and pipe are filled with water. In use, a person pushes down upon the smaller piston and the water pushes upward on the larger piston. The diameter of the smaller piston is 2.20 centimeters. The diameter of the larger piston is 21.0 centimeters. On top of the larger piston is a metal support and on top of that is a car. The combined mass of the support-plus-car is 998 kg. Find the force that the person must exert on the smaller piston to raise the car at a constant velocity. Neglect the masses of the pistons.
Solution
We start our solution with a sketch.
DS = 2.20 cmDL = 21.0 cm
Now, let’s find the force RN exerted on the larger piston by the car support. By Newton’s 3rd Law, it is the same as the normal force FN exerted by the larger piston on the car support. We’ll draw and analyze the free body diagram of the car-plus-support to get that.
F = mFN
Table of ForcesSymbolNameAgentVictimF=mGravitational Force on Support-Plus-CarThe Earth’s Gravitational FieldThe Support-Plus-CarFNNormal ForceThe Large PistonThe Support-Plus-Car
Now we analyze the equilibrium of the larger piston to determine what the pressure in the fluid must be in order for the fluid to exert enough force on the piston (with the car-plus-support on it) to keep it moving at constant velocity.
RN = = 9780 newtons
Table of ForcesSymbolNameAgentVictimRN = = 9780 newtonsInteraction Partner to Normal Force (see above)Support (That part, of the hydraulic lift, that the car is on.)Large PistonFPLPressure-Related Force on Large PistonThe WaterLarge Piston
FPL = PAL
AL is the area of the face of the larger piston. We can use the given larger piston diameter DL = 0.210 m to determine the area of the face of the larger piston as follows:
where is the radius of the larger piston.
Substituting this and the value RN = FN = 9780 newtons into equation 34‑1 above yields
(We intentionally keep 3 too many significant figures in this intermediate result.)
Now we just have to analyze the equilibrium of the smaller piston to determine the force that the person must exert on the smaller piston.
FPERSON
FPS = PAS
The area AS of the face of the smaller piston is just pi times the square of the radius of the smaller piston where the radius is , half the diameter of the smaller piston. So:
FPERSON = 107 N
Fluid in Motion—the Continuity Principle
The Continuity Principle is a fancy name for something that common sense will tell you has to be the case. It is simply a statement of the fact that for any section of a single pipe, filled with an incompressible fluid (an idealization approached by liquids), through which the fluid with which the pipe is filled is flowing, the amount of fluid that goes in one end in any specified amount of time is equal to the amount that comes out the other end in the same amount of time. If we quantify the amount of fluid in terms of the mass, this is a statement of the conservation of mass. Having stipulated that the segment is filled with fluid, the incoming fluid has no room to expand in the segment. Having stipulated that the fluid is incompressible, the molecules making up the fluid cannot be packed closer together; that is, the density of the fluid cannot change. With these stipulations, the total mass of the fluid in the segment of pipe cannot change, so, any time a certain mass of the fluid flows in one end of the segment, the same mass of the fluid must flow out the other end.
Position 2
Position 1
Segment of Pipe Filled with the Fluid that is Flowing Through the Pipe
This can only be the case if the mass flow rate, the number of kilograms-per-second passing a given position in the pipe, is the same at both ends of the pipe segment.
(34-2)
An interesting consequence of the continuity principle is the fact that, in order for the mass flow rate (the number of kilograms per second passing a given position in the pipe) to be the same in a fat part of the pipe as it is in a skinny part of the pipe, the velocity of the fluid (i.e. the velocity of the molecules of the fluid) must be greater in the skinny part of the pipe. Let’s see why this is the case.
Here, we again depict a pipe in which an incompressible fluid is flowing.
Position 2
Position 1
m1
m2V2
2
V1
1
x2
x1
Segment of Pipe Between Positions 1 and 2
Keeping in mind that the entire pipe is filled with the fluid, the shaded region on the left represents the fluid that will flow past position 1 in time t and the shaded region on the right represents the fluid that will flow past position 2 in the same time t. In both cases, in order for the entire slug of fluid to cross the relevant position line, the slug must travel a distance equal to its length. Now the slug labeled m2 has to be longer than the slug labeled m1 since the pipe is skinnier at position 2 and by the continuity equation m1 = m2 (the amount of fluid that flows into the segment of the pipe between position 1 and position 2 is equal to the amount of fluid that flows out of it). So, if the slug at position 2 is longer and it has to travel past the position line in the same amount of time as it takes for the slug at position 1 to travel past its position line, the fluid velocity at position 2 must be greater. The fluid velocity is greater at a skinnier position in the pipe.
Let’s get a quantitative relation between the velocity at position 1 and the velocity at position 2. Starting with
we use the definition of density to replace each mass with the density of the fluid times the relevant volume:
Dividing both sides by the density tells us something you already know:
As an aside, we note that if you divide both sides by t and take the limit as t goes to zero, we have which is an expression of the continuity principle in terms of volume flow rate. The volume flow rate is typically referred to simply as the flow rate. While we use the SI units for flow rate, the reader may be more familiar with flow rate expressed in units of gallons per minute.
Now back to our goal of finding a mathematical relation between the velocities of the fluid at the two positions in the pipe. Here we copy the diagram of the pipe and add, to the copy, a depiction of the face of slug 1 of area A1 and the face of slug 2 of area A2.
Position 1Position 212m1V1m2V2x2x1A1A2
We left off with the fact that V1 = V2 . Each volume can be replaced with the area of the face of the corresponding slug times the length of that slug. So,
Recall that is not only the length of slug 1, it is also how far slug 1 must travel in order for the entire slug of fluid to get past the position 1 line. The same is true for slug 2 and position 2. Dividing both sides by the one time interval t yields:
Taking the limit as t goes to zero results in:
This is the relation, between the velocities, that we have been looking for. It applies to any pair of positions in a pipe completely filled with an incompressible fluid. It can be written as
(34-4)
which means that the product of the cross-sectional area of the pipe and the velocity of the fluid at that cross section is the same for every position along the fluid-filled pipe. To take advantage of this fact, one typically writes, in equation form, that the product A at one location is equal to the same product at another location. In other words, one writes equation 34-3.
Note that the expression A , the product of the cross-sectional area of the pipe, at a particular position, and the velocity of the fluid at that same position, having been derived by dividing an expression for the volume of fluid V that would flow past a given position of the pipe in time t, by t, and taking the limit as t goes to zero, is none other than the flow rate (the volume flow rate) discussed in the aside above.
Further note that if we multiply the flow rate by the density of the fluid, we get the mass flow rate.
(34-5)
Fluid in Motion—Bernoulli’s Principle
The derivation of Bernoulli’s Equation represents an elegant application of the Work-Energy Theorem. Here we discuss the conditions under which Bernoulli’s Equation applies and then simply state and discuss the result.
Bernoulli’s Equation applies to a fluid flowing through a full pipe. The degree to which Bernoulli’s Equation is accurate depends on the degree to which the following conditions are met:
1) The fluid must be experiencing steady state flow. This means that the flow rate at all positions in the pipe is not changing with time.
2) The fluid must be experiencing streamline flow. Pick any point in the fluid. The infinitesimal fluid element at that point, at an instant in time, traveled along a certain path to arrive at that point in the fluid. In the case of streamline flow, every infinitesimal element of fluid that ever finds itself at that same point traveled the same path. (Streamline flow is the opposite of turbulent flow.)
3) The fluid must be non-viscous. This means that the fluid has no tendency to “stick to” either the sides of the pipe or to itself. (Molasses has high viscosity. Alcohol has low viscosity.)
Consider a pipe full of a fluid that is flowing through the pipe. In the most general case, the cross-sectional area of the pipe is not the same at all positions along the pipe and different parts of the pipe are at different elevations relative to an arbitrary, but fixed, reference level.
Position 2
P2
2
Position 1
P1
h2
1
h1
Pick any two positions along the pipe, e.g. positions 1 and 2 in the diagram above. (You already know that, in accord with the continuity principle, .) Consider the following unnamed sum of terms:
where, at the position under consideration:
P is the pressure of the fluid,
(the Greek letter rho) is the density of the fluid,
is the magnitude of the velocity of the fluid,
is the near-surface magnitude of the earth’s gravitational field, and
h is the elevation, relative to a fixed reference level, of the position in the pipe.
The Bernoulli Principle states that this unnamed sum of terms has the same value at each and every position along the pipe. Bernoulli’s equation is typically written:
(34-6)
but to use it, you have to pick two positions along the pipe and write an equation stating that the
value of the unnamed sum of terms is the same at one of the positions as it is at the other.
A particularly interesting characteristic of fluids is incorporated in this equation. Suppose positions 1 and 2 are at one and the same elevation as depicted in the following diagram:
Position 1Position 212P1P2
Then in equation 34-7 and equation 34-7 becomes:
Check it out. If then P2 must be less than P1 in order for the equality to hold. This equation is saying that, where the velocity of the fluid is high, the pressure is low.
